Cisco 3560-CX Switch 8 GE
Uplinks: 2 x 1G SFP and 2 x 1G copper, IP Base

Small form factor; fanless design; silent operation

The switch can be used in open workspaces and other areas that cannot tolerate equipment noise and where multiple cable runs could be difficult, expensive, and intrusive.

Flexible mounting options

The switch can be mounted on the wall, under a desk, rack, DIN rail, or practically anywhere they are needed.

Cisco Multigigabit Ethernet

With the enormous growth of 802.11ac and new wireless applications, wireless devices are driving the demand for more network bandwidth. This creates a need for a technology that supports speeds higher than 1 Gbps on all cabling infrastructure. Cisco Multigigabit Ethernet technology is a unique Cisco innovation that allows you to achieve bandwidth between speeds of 100Mbps and 10 Gbps over traditional Cat 5e cabling or above. In addition, the Multigigabit ports on the Cisco Catalyst Compact switch support PoE+, which is increasingly important for next-generation workspaces and Internet of Things (IoT) ecosystems. The Multigigabit Ethernet ports can also be used as uplinks to connect to traditional access switches such as the Cisco Catalyst 3850/4500 switches.

Cisco Multigigabit technology offers significant benefits for a diverse range of speeds, cable types, and PoE power. The benefits can be grouped into three different areas:

●Multiple speeds:Cisco Multigigabit technology supports autonegotiation of multiple speeds on switch ports. The supported speeds are 100 Mbps, 1 Gbps, 2.5 Gbps, and 5 Gbps on Cat 5e cable and up to 10 Gbps over Cat 6a cabling.

●Cable type:The technology supports a wide range of cable types, including Cat 5e, Cat 6, and Cat 6a or above.

●PoE power:The technology supports PoE and PoE+ for all the supported speeds and cable types.

10-Gigabit SFP+ uplinks

Accommodates business growth and increased traffic, such as aggregate upstream gigabit traffic loads from 802.11ac Wi-Fi access points.

Increased PoE+ Scale

Provides up to 240W of PoE+ budget (twice the power per switch than previous series).

Perpetual PoE

Provides uninterrupted power to a powered-down device even when the switch is booting. This eliminates the need for a backup power source.

PoE pass-through

PoE pass-through gives the ability to power PoE end devices through drawing Cisco UPOE from the wiring closet. The Cisco Catalyst WS-C3560CX-8PT-S has eight downlink ports with two Cisco UPOE input ports that allow it to be powered by another switch. These switches do not need a power supply and receive power over the uplink from an upstream PoE or Cisco UPOE device, providing deployment flexibility and availability. These switches are ideal for wiring-constrained and space-constrained applications.

• Cisco Smart Install enables the configuration of the Cisco IOS Software image and switch without user intervention.
• Cisco Auto Smartports provides automatic configuration as end devices connect to the switch port, allowing autodetection and plug-and-play of the device onto the network. Interface templates containing configurations or policies that can be applied to ports are also supported.
• Cisco Smart Troubleshooting is an extensive array of debug diagnostic commands and system health checks, including Generic Online Diagnostics (GOLD) and Onboard Failure Logging (OBFL).
• Embedded Event Manager (EEM), supported on the Cisco Catalyst 3560-CX, provides real-time network event detection and onboard automation. You can adapt the behavior of your network devices to align with business needs.

• Cisco Prime® Infrastructure provides comprehensive network lifecycle management with an extensive library of features that automate initial and day-to-day management. Cisco Prime integrates hardware and software platform expertise and operational experience into a powerful set of workflow-driven configuration, monitoring, troubleshooting, reporting, and administrative tools.
• Cisco Network Assistant is a PC-based, centralized network management and configuration application for small and medium-sized business (SMB) with up to 250 users. An intuitive GUI lets you easily apply common services across Cisco switches, routers, and access points.
• Cisco Active Advisor is a cloud-based service that provides essential lifecycle information about your network inventory. Available by itself or as a component of other Cisco network management applications, it helps you reduce your network’s overall risk by keeping you up-to-date on the status of your products.

• Link Aggregation Control Protocol (LACP) for creating Ethernet channeling with devices that conform to IEEE 802.3ad. Similar to Cisco EtherChannel technology and PAgP.
• Dynamic Host Configuration Protocol (DHCP) autoconfiguration of multiple switches through a boot server.
• Multicast VLAN Registration (MVR) continuously sends multicast streams in a multicast VLAN. Isolates streams from subscriber VLANs for bandwidth and security reasons.
• Voice VLAN keeps voice traffic on a separate VLAN for easier administration and troubleshooting
• Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk configuration across all switches.
• Remote Switch Port Analyzer (RSPAN) allows administrators to remotely monitor ports in a Layer 2 switch network from any other switch in the same network
• For enhanced traffic management, monitoring, and analysis, the Embedded Remote Monitoring (RMON) software agent supports four RMON groups (history, statistics, alarms, and events).

• Cisco TrustSec SXP support to simplify security and policy enforcement throughout the network. For more information about Cisco TrustSec security solutions, visit cisco.com/go/TrustSec.
• Hardware on the Cisco Catalyst 3560-CX for IEEE 802.1AE MACsec for Layer 2, line-rate Ethernet data confidentiality and integrity on host-facing ports. Protects against man-in-the-middle attacks (snooping, tampering, and replay).
• Flexible authentication that supports multiple authentication mechanisms including 802.1X, MAC Authentication Bypass, and web authentication using a single, consistent configuration. ● Monitor mode that creates a user-friendly environment for 802.1X operations.
• RADIUS change of authorization and downloadable ACLs for comprehensive policy management.
• 802.1X supplicant with Network Edge Access Transport (NEAT) for extended secure access; compact switches in the conference rooms have the same level of security as switches inside a locked wiring closet.

Switch Hibernate Mode

Innovative technology that puts the switch in an ultra-low power mode during periods of nonoperation such as nights and weekends. The switch can be configured to be in the hibernate mode using the Cisco Energy Management Suite.

IEEE 802.3az or Energy-Efficient Ethernet (EEE)

Ports dynamically sense idle periods between traffic bursts and quickly switch the interfaces into a low-power idle mode, reducing power consumption.

Perpetual PoE

Provides uninterrupted power to a powered-down device even when the switch is booting. This eliminates the need for a backup power source.

PoE pass-through

PoE pass-throughgives the ability to power PoE end devices through drawing Cisco UPOE from the wiring closet. The Cisco Catalyst 3560CX-8PT-S has eight downlink ports with two Cisco UPOE input ports that allow it to be powered by another switch. These switches do not need a power supply and receive power over the uplink from an upstream PoE or Cisco UPOE device, providing deployment flexibility and availability.

Power Supply

80-Plus Silver Certified.

Application Visibility

NetFlow Lite lets you maintain awareness of all application traffic on the network. It helps capture and record specific packet flows. Exports flow data in the NetFlow Version 9 format for analysis on a wide range of Cisco and third-party collectors.

Advanced Quality of Service

• Up to eight egress queues per port and strict priority queuing so that the highest priority packets are serviced ahead of all other traffic.
• Shaped Round Robin (SRR) scheduling and Weighted Tail Drop (WTD) congestion avoidance.
• Flow-based rate limiting and up to 256 aggregate or individual policers per port.

3560CX-8TC-S

8 x 10/100/1000 Gigabit Ethernet

NA

-

2 x 1G copper plus 2 x 1G SFP

IP Base (IP Services with RTU License)

3560CX-12TC-S

12 x 10/100/1000 Gigabit Ethernet

NA

-

2 x 1G copper plus 2 x 1G SFP

IP Base (IP Services with RTU License)

3560CX-8PC-S

8 x 10/100/1000 Gigabit Ethernet

8 PoE+

240W

2 x 1G copper plus 2 x 1G SFP

IP Base (IP Services with RTU License)

3560CX-12PC-S

12 x 10/100/1000 Gigabit Ethernet

12 PoE+

240W

2 x 1G copper plus 2 x 1G SFP

IP Base (IP Services with RTU License)

3560CX-12PD-S

12 x 10/100/1000 Gigabit Ethernet

12 PoE+

240W

2 x 1G copper plus 2 x 10G SFP+

IP Base (IP Services with RTU License)

C3560CX-8PT-S

8 x 10/100/1000 Gigabit Ethernet

8 PoE+

Up to 146W

2 x 1G copper (Cisco UPOE+ uplinks)

IP Base (IP Services with RTU License)

C3560CX-8XPD-S

6 x 10/100/1000 Gigabit Ethernet plus
2 Multigigabit Ethernet 100/2500/5000/10000

8 PoE+

240W

2 x 10G SFP+

IP Base (IP Services with RTU License)

3560CX-8TC-S

Internal power supply

0W

No

3560CX-12TC-S

Internal power supply

0W

No

3560CX-8PC-S

Internal power supply

240W

No

3560CX-12PC-S

Internal power supply

240W

No

3560CX-12PD-S

Internal power supply

240W

No

C3560CX-8PT-S

1 PoE uplink

0W

No

2 PoE uplinks

0W

Yes

1 PoE+ uplink

0W

Yes

2 PoE+ uplinks

20W

Yes

1 Cisco UPOE uplink

22W

Yes

2 Cisco UPOE uplinks

68W

Yes

Auxiliary input

54W

Yes

1 PoE uplink plus auxiliary input

65W

Yes

2 PoE uplinks plus auxiliary input

76W

Yes

1 PoE+ uplink plus auxiliary input

76W

Yes

2 PoE+ uplinks plus auxiliary input

98W

Yes

1 Cisco UPOE uplink plus auxiliary input

100W

Yes

2 Cisco UPOE uplinks plus auxiliary input

146W

Yes

3560CX-8XPD-S

Internal power supply

240W

No

2960CX-8TC-L

8 x 10/100/1000 Gigabit Ethernet

N/A

-

2 x 1G copper plus 2 x 1G SFP

LAN Base

2960CX-8PC-L

8 x 10/100/1000 Gigabit Ethernet

8 PoE+

124W

2 x 1G copper plus 2 x 1G SFP

LAN Base